Tile attachment
Each tile is secured to the deck or battens in a pattern set by the tile profile.
Tile Roofing
Tile Roof Installation Maplewood, NJ
Tile roof installation in Maplewood covers more than the tile: the framing check, underlayment, battens, fasteners, flashing and ridge all decide how long the roof lasts. One call to (973) 858-1830 reaches a nearby tile installer.
Before any tile goes up, the question is whether the house can hold it. A tile roof weighs several times as much as asphalt shingles, and a home built for shingles may need an engineer to check the rafters or trusses before switching. Houses designed for tile already account for that load in their framing.
Then comes choosing the tile itself. Clay holds its color through the whole tile and lasts for generations, and concrete tile is heavier, more absorbent and offers a wide range of shapes and finishes. Shapes range from flat and low profile tile to high profile S tile and traditional barrel tile.
The tile may last generations, but the layers below it decide when the roof leaks. Most tile needs a slope of at least 2.5 in 12, and building codes call for a doubled underlayment on slopes below 4 in 12. Investing in the underlayment up front is what lets the tile live out its full life.
Depending on what the roofer finds, tile roof installation in Maplewood, NJ can go hand in hand with tile roof replacement and roof installation.
Looking for Maplewood tile roof installation? Call (973) 858-1830 and describe the problem to a roofer who works in Maplewood.
Call nowThe process
What happens during a tile roof installation
A tile roof goes on in layers, and the tile is the last of them.
Plan for the load
The job starts with the structure: span tables or an engineer confirm the framing, and the building permit is secured. Extra tile is ordered so there are matching spares for repairs later.
Lay the underlayment
Decking is checked and fastened, drip edge goes on, and the deck is covered with the chosen underlayment, with self-adhered membrane in valleys and at eaves where ice or wind-driven rain is a concern. Since this layer does the waterproofing, it is where quality matters most.
Set the battens
Battens run horizontally to hold each course of tile, often raised on counter battens to leave a drainage and air space below. Some systems skip battens and fasten tile directly, depending on the profile and the slope.
Flash every penetration
Valley metal, wall and headwall flashing, chimney flashing and soft metal flashing for vent pipes go in before and during tiling. Flashing for tile is built for the depth of the tile, which is why shingle flashing details do not carry over.
Lay the tile
Tile goes on from the eave up, with an eave closure to keep birds out and fasteners or foam adhesive chosen for local wind requirements. Cut tiles at hips and valleys are fastened too, since small pieces are the first to blow off.
Cap the ridge
Ridge and hip caps are set on a raised ridge board, either in mortar or with a dry ridge system and a vented closure that lets attic air out. The roof is cleaned, broken pieces are replaced and spares are left with the owner.
What is included
What tile roof installation includes
Ridge finish
Eave and ridge details are finished to complete the system.
Waterproof layer
The deck is covered with underlayment suited to the slope lapped to shed water to the eaves.
Structural review
The framing is checked for the weight of tile and reinforced where needed.
Tile flashing
Wide valley metal and shaped wall flashings are installed to handle the deep curves of tile.
Related service
Barrel Tile Roof Installation Maplewood, NJ
Barrel tile is the classic two-piece tile roof: half-round pan tiles laid concave side up, with cover tiles laid over the joints between them. Their tapered shape and deep profile create the rolling texture that defines the style. Because of that depth, barrel tile needs careful work at the eaves, hips and ridges, where the open curves must be closed off.
Barrel tile roof installation in Maplewood calls for extra attention to fastening, since cover tiles sit high and catch wind. Pans and covers have to run in straight lines with even exposure, which takes careful layout before the first pan goes down.
Related service
Spanish Tile Roof Installation Maplewood, NJ
Spanish tile usually means the S-shaped profile that combines a pan and a cover in a single piece, giving the look of barrel tile with half the pieces. Clay and concrete Spanish tile are both common, in solid and blended colors. Side interlocks help it shed water, though the curved ends need bird stops and ridge closures just like barrel tile.
For Spanish tile roof installation in Maplewood, the underlayment and flashing matter as much as the look of the tile. Where the tile meets walls and chimneys, flashing is shaped to fill the curve without leaving gaps. If you choose a blend, the roofer mixes tile from several pallets at once to spread the color evenly.
Local help
Tile Roof Installation Near Me
Tile roofs in Maplewood go onto newer homes built for them and onto older homes where owners are switching from shingles. Homes in Maplewood and surrounding areas such as Vauxhall, Union, Springfield and Short Hills that were framed for shingles often need a structural review before tile is an option, while homes already built for tile can usually go straight to choosing a profile and color.
Need tile roof installation around Maplewood? Call (973) 858-1830 for a Maplewood roofer who serves the towns around it too.
What the local climate does to a roof
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, which is how ice dams form and back water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. Most homeowners in Maplewood, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why fix it now
Smaller repairs
Small roof problems caught early usually stay small repairs.
Local knowledge
Local roofers see the same roofs and storm damage across Maplewood and nearby towns.
Clear next steps
Ask your questions before you agree to anything.
Tile Roof Installation questions
Can my house hold a tile roof?
Clay and concrete tile are among the heaviest roof coverings, several times the weight of shingles. Whether a given house can carry it depends on the framing, which is why conversions from shingles start with a structural review. Some lighter weight tile products are made for homes with less structural capacity.
Can tile go over old shingles?
A tile roof needs a bare deck, so existing shingles or other roofing are removed. Removing the old roof also takes weight off the framing, which matters with a material this heavy.
What underlayment goes under a tile roof?
The common choices are felt, synthetic underlayment and self-adhered membrane. The underlayment usually wears out long before the tile, so a durable one delays the first relay. Codes call for two layers on slopes from 2.5 in 12 up to 4 in 12.
How long does it take to put on a tile roof?
A typical home takes longer than a shingle roof, often one to a few weeks depending on size, complexity and weather. Complex rooflines and framing work before tiling can stretch the schedule. Once the underlayment is down, the house is protected from rain while tile goes on.
What is better, clay or concrete tile?
Both make durable roofs with different tradeoffs. Clay tile resists fading and has lasted a century or more on some older buildings. Concrete is sturdy and widely available, though it absorbs more moisture and its surface weathers with age.
More questions? Call (973) 858-1830
Related services
Tile Roof Replacement
Full tile roof replacement when the underlayment, fasteners or tile have reached the end of their life, so the layers under the tile last as long as the tile.
Learn moreRoof Installation
Installing a new roof layer by layer, from drip edge and underlayment to flashing, vents and the finished roofing, so it sheds water at every edge and seam.
Learn moreTile Roof Inspection
A close look at the tile, underlayment, flashing, valleys and attic of a clay or concrete tile roof, before buying a home, after a storm or as the underlayment ages.
Learn moreRoof Ventilation
Balancing attic intake and exhaust with soffit vents, ridge vents and attic fans, so shingles and decking last as long as they should.
Learn more
Looking for something else?
See all roofing servicesTalk to a Maplewood roofer about tile roof installation
Call (973) 858-1830 to talk to a roofer serving Maplewood, NJ.