Ridge ventilation
Closures fill the gaps under the trim while keeping out rain and pests.
A roofer in Maplewood can install a new metal roof in standing seam, exposed fastener panels, metal shingles or stone coated steel, so the roof is set up for decades of service. Dial (973) 858-1830 to talk with a local roofer about a metal roof.
Before anything else, a metal roof starts with picking how the panels attach. Exposed fastener panels, such as corrugated and ribbed panels, are screwed through the face and go on quickly, but every screw has a washer that will need attention someday. With standing seam, hidden clips hold the panels and let them move, which is why it is the premium residential choice.
After the system comes the material. Most residential panels are coated steel, with aluminum preferred near the coast and copper or zinc used for accents and high-end work. Gauge and paint system both affect how the roof ages, with thicker metal and PVDF finishes lasting best.
The layers below the panels decide how quiet and dry the roof is. A solid deck covered with high-temperature underlayment is the usual base, plus ice and water shield at eaves and valleys where needed. Some barns and shops use purlins instead, but a house roof is quieter and drier over a deck.
Many metal roof installation calls in Maplewood also turn up a need for standing seam metal roof or metal roof replacement.
Need metal roof installation in Maplewood? Call (973) 858-1830 to talk to a local roofer.
Call nowHere is the usual order for a new metal roof.
Panel profile, gauge, paint system and color are settled, and the roof is measured so panels can be cut to length. Many panels are made to the exact length of each slope.
The deck is stripped, repaired and checked for flatness, since metal panels show every dip. Bad decking telegraphs right through thin metal.
High-temperature synthetic underlayment covers the deck, with ice and water shield at the eaves and valleys where required. This layer is the backup if water ever gets past the metal.
Eave trim and drip edge go on first, along with valley flashing, so panels can lap over them. The order of trim matters because every piece has to lap water downhill.
Standing seam panels are clipped and seamed, while exposed fastener panels are screwed through the flat or the rib as the profile requires. Screws are driven snug, never crushed, so the washer seals.
The ridge, walls, chimneys and pipes are flashed, and closures seal the gaps under the trim. On roofs that hold snow, snow guards keep it from sliding off in a sheet.
Closures fill the gaps under the trim while keeping out rain and pests.
The right profile, metal and gauge for the house with a finish chosen for long color life.
Pipe boots made for metal and snow guards over entries finish the job for safety and a dry roof.
All trim in matching color and metal for a clean, finished look.
A heat-rated synthetic underlayment covers the deck as a second layer of protection.
Choosing a metal roofing contractor means finding someone who installs metal regularly, not occasionally. Good questions cover the panel systems they install, the underlayment they use and how they detail valleys and walls.
A metal roofing contractor in Maplewood should talk you through panel, gauge, finish and snow guards without pushing one answer. Ask to see a few local roofs they have done, and look at how straight the panels run and how the trim meets the walls.
Stone coated steel is formed steel topped with granules so it resembles tile, shake or dimensional shingles. It is lighter than tile, resists wind and hail well, and the granules soften the sound of rain.
The panels often hang on wood battens, which lift them off the deck for airflow. It suits Maplewood homes where heavy tile would need framing upgrades.
A metal shingle roof uses smaller interlocking pieces stamped to look like shingles, slate or shake. They fasten through concealed edges and work well on cut-up roofs.
A metal shingle roof gives a Maplewood home the look of shingles or slate with the lifespan of metal. Each shingle line has its own starter, trim and fastening pattern.
In Maplewood, homeowners choose metal for its long life, wind resistance and the way it sheds snow. Across Maplewood and nearby communities including Vauxhall, Union, Springfield and Short Hills, metal roofs suit older farmhouses and new builds alike, and a roofer who installs metal regularly will know which system fits each kind of building.
For metal roof installation in Maplewood, NJ or nearby towns like Vauxhall, Union, Springfield and Short Hills, call (973) 858-1830 to reach a roofer who covers your street.
Cold winters bring snow, ice and a long stretch of freezing nights. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, building ice dams that push water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. Most homeowners in Maplewood, NJ have the roof checked in the fall and again after the snow melts.
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Roofers in Maplewood know the roof types and weather wear common in local homes.
Ask the roofer about the cause, the options and the estimate before work starts.
More questions? Call (973) 858-1830
Standing seam metal roofing installed, repaired and detailed for thermal movement, for homes, additions and low slope roofs.
Learn moreReplacing a rusted or worn-out metal roof, or swapping an old shingle roof for new metal, so the new roof starts on a sound base.
Learn moreInstalling a new roof layer by layer, from drip edge and underlayment to flashing, vents and the finished roofing, so it sheds water at every edge and seam.
Learn moreInstalling, replacing and repairing metal roofs on warehouses, shops, offices and other commercial buildings, planned around the building and its operations.
Learn moreLooking for something else?
See all roofing servicesCall (973) 858-1830 to talk to a roofer serving Maplewood, NJ.