Rotted board repair
Damaged fascia is replaced with primed wood or PVC and scarfed into the existing board.
Exterior Services
Fascia Repair Maplewood, NJ
A Maplewood roofer can repair the fascia boards that carry your gutters and cap the ends of the rafters, and check the rafter tails behind the board while it is off. Dial (973) 858-1830 to talk with a local roofer about the fascia.
When a fascia board goes soft, the cause is almost always water running down the back of the gutter instead of into it. A missing or short drip edge lets rain curl under the shingles and run down the face of the board, while clogged gutters overflow over the back edge and soak it. Over a few seasons the wood softens, the gutter screws lose their grip and the gutter starts to sag or pull away.
Fascia damage does not stay in the fascia for long. Left alone, the rot moves into the rafter ends and the edge of the roof deck, which turns a trim repair into structural work. Aluminum wrap over wood can hide all of this, since the metal looks fine while the board behind it crumbles.
A few observations make the first conversation more useful. Note where paint is peeling, where gutters sag or have pulled away, and whether water pours over the gutter in heavy rain. Say whether the fascia is bare wood, painted, PVC or wrapped in metal, since that changes the repair.
Depending on what the roofer finds, fascia repair in Maplewood, NJ can go hand in hand with soffit repair and gutter installation.
Dealing with this in Maplewood, NJ right now? Call (973) 858-1830 to talk to a local roofer.
Call nowThe process
The fascia repair process
A fascia repair only lasts if the water that rotted it is redirected.
Check the edge
Before the board comes off, the roofer looks at what has been soaking it, from the shingle edge to the downspout. An awl or screwdriver finds the edges of the soft wood.
Remove the gutter
To reach the fascia, the gutter over it is removed and the hangers pulled. This is a good time to check the gutter itself for leaks and bad seams.
Repair the framing
The roofer looks at the rafter ends and the sub-fascia, since soft framing will not hold a new board. Skipping it is the most common reason fascia fails twice.
Install new fascia
A replacement board matched to the existing size goes up, sealed at the ends and joints. PVC and composite boards do not rot and hold paint well.
Fix the edge flashing
Drip edge flashing is slid under the shingles and over the gutter back, so water cannot reach the wood. It is a small part that does most of the work.
Rehang the gutter
The gutter is reattached with hangers spaced closely enough to carry water and debris. The finished edge is checked with a hose or after the next rain.
What is included
What fascia repair covers
Gutter reattachment
Sagging gutters are rehung on solid fascia with new hangers with screws instead of loose spikes.
Drip edge installation
New drip edge is tucked under the shingles over the gutter so water drops into the gutter.
Rafter tail repair
Rotted rafter ends behind the fascia are sistered or rebuilt before the fascia goes back on.
Fascia wrapping
Sound wood fascia can be covered with formed aluminum or vinyl wrap once any rot is gone.
Related service
Fascia Board Replacement Maplewood, NJ
Fascia board replacement means taking off whole lengths of board rather than patching short sections. Replacing the whole run gives the roofer a clear look at every rafter tail and the edge of the roof deck. It is also the moment to choose a material, whether primed wood, PVC, composite or wood with an aluminum wrap.
For many Maplewood homes it makes sense to replace fascia while the gutters are off for replacement anyway. Ask whether the roofer plans to remove the old boards or wrap over them, because wrapping soft wood only hides the rot. The new boards should match the old width so the soffit closes properly.
Related service
Fascia Board Repair Maplewood, NJ
Localized fascia damage, often at corners and below gutter joints, can usually be repaired without replacing the whole board. A scarf joint, cut at an angle and glued and fastened, blends the new piece into the old board and sheds water better than a square butt joint. Minor surface damage may only need consolidant, filler and paint.
Patching a fascia board in Maplewood without fixing the gutter or drip edge above it just buys a season or two. Common fixes include a resealed gutter joint, a cleared outlet or a new length of drip edge. Done right, the repair is hard to spot once painted.
Local help
Fascia Repair Near Me
Fascia repair calls in Maplewood come from older homes with painted wood trim and newer homes with aluminum-wrapped edges alike. Homes in Maplewood and nearby towns like Vauxhall, Union, Springfield and Short Hills range from older houses with wood fascia that needs regular paint to newer builds where metal wrap can hide rot underneath, which is why keeping gutters clear does so much to protect the fascia.
Searching for fascia repair near me from Maplewood or Vauxhall, Union, Springfield and Short Hills? Call (973) 858-1830 to talk to a roofer who works in your part of town.
How the weather here affects roofs around Maplewood
Cold winters bring snow, ice and a long stretch of freezing nights. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, building ice dams that push water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. Most homeowners in Maplewood, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why not wait
Smaller repairs
Small roof problems caught early usually stay small repairs.
Local knowledge
Local roofers see the same roofs and storm damage across Maplewood and nearby towns.
Clear next steps
Ask your questions before you agree to anything.
Fascia Repair questions
Do I need new fascia boards or just a repair?
Repair is fine when damage is limited to a few spots and the rafter tails are sound. If the damage is widespread, new boards end up being the simpler fix. Either way, the rafter tails behind the board need to be checked.
What causes fascia boards to rot?
Water getting behind the gutter is the main cause. Clogs, bad seams and the lack of a drip edge are the usual culprits. Once the paint fails, the wood takes on water quickly.
Should I cover rotted fascia with metal?
Wrapping over soft fascia traps moisture and lets the rot continue unseen. The gutter hangers still screw into the wood behind the wrap, so they loosen as the board softens. Wrap is a good finish over new or solid fascia.
Do fascia boards affect my gutters?
The fascia is what gutters are fastened to. When the wood softens, hanger screws and spikes lose grip and the gutter sags, tips forward or pulls away. Repairing the fascia and rehanging the gutter with hidden hangers fixes both problems at once.
What is the best material for fascia?
Primed wood, PVC, composite and aluminum-wrapped wood are the usual choices. Wood looks traditional and is easy to work with, though it needs upkeep. The drip edge and gutters decide how long any fascia lasts.
More questions? Call (973) 858-1830
Related services
Soffit Repair
Fixing damaged soffits, blocked soffit vents and gaps where animals get in, matched to what is causing the damage in the first place.
Learn moreGutter Installation
New gutters and downspouts formed to fit the house, with the right size, pitch and outlet placement, with the fascia checked before anything is hung.
Learn moreGutter Repair
Fixing gutters that drip at the corners, sag between hangers or pull away from the fascia, without replacing gutters that still have life in them.
Learn moreRoof Repair
Targeted roof repairs for wind, age and water damage, matched to what is actually wrong up top.
Learn more
Looking for something else?
See all roofing servicesNeed fascia repair in Maplewood, NJ?
Call now for Maplewood fascia repair and help in the towns around it.